? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded power inductors C lps3010 document 428-1 document 428-1 revised 08/05/09 dcr srf i sat (a) 5 i rms (a) 6 inductance 2 max 3 typ 4 10% 20% 30% 20c 40c part number 1 20% (h) (ohms) (mhz) drop drop drop rise rise lps3010-471ml_ 0.47 0.070 370 1.8 1.9 2.0 1.3 1.80 lps3010-681ml_ 0.68 0.080 270 1.6 1.7 1.7 1.3 1.75 lps3010-102ml_ 1.0 0.085 230 1.5 1.6 1.6 1.1 1.50 lps3010-152ml_ 1.5 0.120 165 1.3 1.4 1.4 1.05 1.40 lps3010-182ml_ 1.8 0.150 150 1.2 1.2 1.3 1.00 1.40 lps3010-222ml_ 2.2 0.220 130 1.3 1.4 1.4 0.90 1.10 lps3010-332ml_ 3.3 0.220 110 0.83 0.88 0.90 0.85 1.10 lps3010-472ml_ 4.7 0.300 92 0.72 0.75 0.77 0.70 0.95 lps3010-562ml_ 5.6 0.400 80 0.67 0.69 0.71 0.60 0.78 lps3010-682ml_ 6.8 0.450 70 0.61 0.63 0.64 0.56 0.74 lps3010-822ml_ 8.2 0.520 62 0.56 0.59 0.59 0.53 0.70 lps3010-103ml_ 10 0.540 58 0.50 0.53 0.55 0.48 0.64 lps3010-123ml_ 12 0.700 47 0.46 0.49 0.50 0.44 0.58 lps3010-153ml_ 15 0.950 43 0.41 0.43 0.44 0.37 0.48 lps3010-183ml_ 18 1.10 40 0.38 0.40 0.41 0.33 0.47 lps3010-223ml_ 22 1.20 36 0.32 0.35 0.36 0.30 0.41 lps3010-333ml_ 33 2.00 27 0.25 0.27 0.28 0.26 0.35 lps3010-473ml_ 47 3.20 21 0.23 0.24 0.25 0.22 0.31 lps3010-683ml_ 68 3.50 21 0.20 0.21 0.22 0.20 0.28 lps3010-104ml_ 100 5.25 14 0.14 0.16 0.17 0.18 0.24 lps3010-124ml_ 120 6.10 12 0.13 0.15 0.15 0.14 0.19 lps3010-154ml_ 150 9.15 11 0.13 0.14 0.14 0.13 0.17 lps3010-184ml_ 180 10.1 9 0.11 0.12 0.13 0.11 0.15 lps3010-224ml_ 220 12.5 8 0.10 0.11 0.12 0.095 0.13 lps3010-334ml_ 330 18.5 7 0.10 0.105 0.115 0.085 0.11 core material ferrite core and winding loss see www.coilcraft.com/coreloss terminations rohs compliant silver-palladium-platinum-glass frit. other terminations available at additional cost. weight 25 ? 32 mg ambient temperature ?40c to +85c with i rms current, +85c to +125c with derated current storage temperature component: ?40c to +125c. packaging: ?40c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 1000/7 reel; 3500/13 reel; plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.4 mm pocket depth recommended pick and place nozzle od: 3 mm; id: 1.5 mm pcb washing only pure water or alcohol recommended ? ultra small 3.0 3.0 mm footprint; less than 1.0 mm tall ? very low dcr; excellent current handling coilcraft designer?s kit c392 contains samples of 0.80 h to 33 h parts (3 each) from lps3008, lps3010 and lps3015. kit c401 contains samples of 0.56 h to 33 h parts (3 each) from lps4012 and lps4018. kit c402 contains samples of 220 h to 3300 h parts (3 each) from all five series. for details of kit contents and to order, contact coilcraft or visit http://order.coilcraft.com . 1. please specify termination and packaging codes: lps3010-223m lc termination: l = rohs compliant silver-palladium- platinum-glass frit. special order: t = rohs tin-silver-copper (95.5/4/0.5) or s = non-rohs tin-lead (63/37). packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (1000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d =13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (3500 parts per full reel). 2. inductance tested at 100 khz, 0.1 vrms using an agilent/hp 4192a. inductance at 1 mhz is the same for parts with srf 10 mhz. 3. dcr measured on a micro-ohmmeter. 4. srf measured using an agilent/hp 8753es or equivalent. 5. dc current that causes the specified inductance drop from its value without current. 6. current that causes the specified temperature rise from 25c ambient. 7. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering.
? coilcraft, inc. 2010 specifications subject to change without notice. please check our website for latest information. shielded smt power inductors C lps3010 series document 428-2 document 428-2 revised 08/05/09 l vs current l vs frequency 0.1 1 10 100 1000 0.01 0.1 10 1 inductance (h) frequency (mhz) 6.8 h 0.68 h 330 h 33 h 3.3 h 68 h 0.1 1 10 100 1000 0.01 0.1 10 1 inductance (h) current (a) 6.8 h 0.68 h 330 h 33 h 3.3 h 68 h -40 -20 0 20 40 60 80 100 140 120 ambient temperature (c) 120 110 100 90 80 70 60 50 40 30 20 10 0 25c percent of rated current i sat i rms 0.116 0.003 2,95 0,076 dash number internal code 0.116 0.003 2,95 0,076 0.130 3,30 0.040 1,02 0.025 0,64 0.045 1,14 0.020 0,51 0.130 3,30 0.035 0.004 0,9 0,1 recommended land pattern 0.035 0,89 winding direction 123x * * dimensions are of the case not including the termination. for maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. * typical current derating dimensions are in inches mm
|
